|
Data Sheet
|
FNP-LED (MIMIC LED Display)
STANDARD FEATURES:
• Available in Red and Charcoal Gray
• Up to 504 LED's can be controlled with FireNET Plus Panel
• Available in 3 different size enclosures
• LED's comes in 3 different colors: Red, Green, or Yellow
• FNP-LED can be easily upgraded onsite with minimal cost and effort |
|
Data Sheet
|
FN-LCD-N (Network Annunciator)
STANDARD FEATURES:
• UL 864 9th edition approved
• 320 character liquid crystal display (8 line x 40 character)
• Dual RS-485 ports for primary fire network
• 2 built-in RS-232 interfaces for programming via a PC and serial printer interface
• True Peer-to-Peer network annunciation |
|
Data Sheet
|
FN-LCD-S (Serial Annunciator)
STANDARD FEATURES:
• UL 864 9th edition approved
• Large 320 character liquid crystal display (8 line x 40 character)
• Resides on the FireNET slave RS-485 lin
|
|
Data Sheet
|
FN-ACC-R/C (Battery/Accessories Enclousure)
STANDARD FEATURES:
• Designed to provide a method to properly store backup batteries for the FireNET and FireNET Plus panels
• The enclosure can also be used to mount 16 Channel I/O Boards
• The battery enclosure comes in two colors Red (FN-ACC-R) & Charcoal (FN-ACC-C), and comes with a keylock
|
|
Data Sheet
Instruction
|
TCF-142-M-ST (Fibre Optic Module)
STANDARD FEATURES:
• Capability to network FireNET™, FireNET Plus, and Network Annunciator using fiber optic cables
• Extends RS-485 transmission up to 3.1 miles
• Protects against electrical interface and chemical corrosion
• No special programming required
• UL 864 9th Edition Liste |
|
Data Sheet
|
FN-4127-SLC (Dual Loop Expander Card for FireNet)
STANDARD FEATURES:
• Adds two SLC loops to a two loop FireNET control panel
• Each SLC loop is capable of 127 sensors/modules, plus 127 analog sounder bases, for a potential total of 254 addresses per loop (127+127 per loop)
• FN-4127-SLC can be added at the factory or installed in the field
• Supports Class A and B wiring methods per NFPA72 Styles 4, 6, and 7 (with isolators)
• Fully supervised & power limited SLC loops
• Supports Hochiki's DCP (Digital. Communication Protocol) loop protocol
• Same functionality as built-in SLC loops of FireNET control panel
• One SLC expander (maximum) may be added per FireNET control panel
• Each SLC loop is completely independent and autonomous
• Uses standard wire, no shielded or twisted pair required on SLC loop |
|
Data Sheet
|
FNP-1127-SLC (Single Loop Expander Card for FireNet Plus)
STANDARD FEATURES:
• Adds one SLC loop to the FireNET Plus (FNP-1127E series) control panel
• The SLC loop is capable of 127 sensors/modules, plus 127 analog sounder bases, for a potential total of 254 addresses
• The FireNET Plus 1127E control panel supports one FNP-1127-SLC, for a total of two SLC loops per panel
• Supports Class A and B wiring methods per NFPA 72 Styles 4, 6, and 7 (Style 7 requires isolators)
• Fully supervised & power limited SLC loop
• Supports Hochiki's DCP (Digital Communication Protocol)
• Same functionality as built-in loop of FireNET Plus control panel
• Uses standard wire; shielded/twisted pair is not required on SLC loops |
|
Data Sheet
|
FN-4127-NIC (Dual RS-485 Network Interface Card)
STANDARD FEATURES:
• Allows for the expansion of up to 64 panels on a FireNET system
• Enables information to be transmitted between control panels
• Network protocol designed for tolerance to interference and data corruption
• Each card configured to a unique address through use of a dipswitch
• Transmission distance of up to 4,000 ft.
• Uses standard type Belden cable suitable for RS-485 applications
• Simple 2-wire loop connection
• Flexible configuration options
• Network wide Cause & Effect logic
• Fully secure against short or open conditions |
|
Data Sheet
|
FN-4127-IO (16 Channel Input/Output Board)
STANDARD FEATURES:
• 16 channels of input/output points
• 32 I/O boards per FireNET panel (512 channels of input/output points)
• Each channel configurable as input or output point
• Inputs are opto-isolated non-supervised pulldown type triggered by
• Outputs are open collector transistor pulldown type (100mA max each) that provide
• Simple 4 wire connection to control panel (2 for power, 2 for data)
• All inputs/outputs can be assigned to global functions, any event category, and used in network wide Cause & Effect logic
• Can be mounted locally within control panel enclosure or remotely via FN-ACC accessory enclosure up to 4000ft from the panel
• Each I/O board has a unique address 1-32 (set via DIP switch) on the I/O Comms Bus
• Input/Outputs are for secondary use, not for primary fire initiation inputs or notification outputs
• Two LED's are provided for communication status |
|
Data Sheet
|
GUS Series (FireNET Graphix Alarm Management Software)
STANDARD FEATURES:
• Choice of text, graphic and event list display when event occurs
• Versatile event analysis
• Total history archive
• Easy to program
• Secure system
• Cost effective compared to other systems
• Simple to use
• Unlimited map linking
• Display and control for multiple panels
• Event history can be viewed, filtered and exported to text or HTML documents |
